Guide · Food
Canning at altitude
Almost all of Utah cans at altitude, and altitude changes the physics: water boils cooler, so a sea-level recipe under-processes. This page teaches the adjustments only — the added minutes and the higher pressures — to apply to a tested recipe. It does not publish recipes.
Updated 2026-11-18
Why altitude changes processing
Air pressure falls as you climb, and water boils at a lower temperature when there is less air pressing on it. Utah State University Extension puts the drop at about 2°F for every 1,000 feet of elevation. Water that boils at 212°F at sea level boils at roughly 202°F at 5,000 feet — and no lid, burner or patience makes an open pot boil hotter than its boiling point.
Cooler water does less work per minute, so the fix splits by canner. In a boiling-water canner you cannot raise the temperature, so you add time. In a pressure canner the sealed steam can still reach temperature — at sea level, 10.5 pounds of gauge pressure holds 240°F inside (NCHFP) — but the same gauge reading delivers a lower temperature up high, so you raise the pressure and keep the recipe's time. Skip the adjustment and harmful organisms, including Clostridium botulinum, may survive (USU Extension).
Two gauges, two different tables
Pressure canners read pressure one of two ways, and the altitude tables differ because the gauges do:
- Dial gauge — a numbered dial on the lid that you hold at an exact pressure by adjusting the heat. It can step up in single pounds, so its table moves in fine 2,000-foot bands. Have a dial gauge checked for accuracy before use each year — many county Extension offices test them (NCHFP). A gauge that reads high under-processes.
- Weighted gauge — a small weight that sits on the vent and rocks or jiggles when the canner holds pressure. It comes in fixed settings — typically 5, 10 and 15 pounds — so it cannot fine-tune for altitude. It needs no accuracy check; the rocking is the check (NCHFP).
One more term, because every tested recipe names it: headspace is the empty space the recipe leaves between the top of the food or liquid and the lid. Leave exactly what the recipe specifies — it is part of how the jar seals and processes.
Boiling-water canning: add time
For high-acid foods in a boiling-water canner, add minutes to the recipe's sea-level processing time based on your elevation (USDA/NCHFP, as tabulated by USU Extension):
| Altitude | Add to processing time |
|---|---|
| 0–1,000 ft | No change |
| 1,001–3,000 ft | 5 minutes |
| 3,001–6,000 ft | 10 minutes |
| 6,001–8,000 ft | 15 minutes |
| 8,001–10,000 ft | 20 minutes |
Many USDA recipes print the adjusted time for your altitude band directly in the recipe's own table. Use one or the other — the recipe's altitude time, or the sea-level time plus this addition — never both. If the recipe prints its own altitude rows, the recipe wins. Start the timer when the water returns to a vigorous boil, and keep at least 1 inch of water over the jar tops (2 inches for processes over 30 minutes).
Pressure canning: raise the pressure, keep the time
For the standard USDA low-acid processes, a dial-gauge canner steps up by altitude band (USU Extension / USDA):
| Altitude | Dial gauge | Weighted gauge |
|---|---|---|
| 0–1,000 ft | 11 lb (0–2,000 ft band) | 10 lb |
| 1,001–2,000 ft | 11 lb | 15 lb |
| 2,001–4,000 ft | 12 lb | 15 lb |
| 4,001–6,000 ft | 13 lb | 15 lb |
| 6,001–8,000 ft | 14 lb | 15 lb |
| 8,001–10,000 ft | 15 lb | 15 lb |
The weighted-gauge rule is the simple one, and NCHFP states it plainly: a weighted gauge cannot correct precisely for altitude, so above 1,000 feet it runs at 15 lb instead of 10. USU says the same for Utah: always use the 15 lb setting above 1,000 feet.
These pressures are for the standard processes built on an 11 lb dial / 10 lb weighted baseline. A few tested processes use a different baseline — the recipe's own altitude table always wins. Whatever the recipe, vent the canner for a full 10 minutes before pressurizing, start timing when the recommended pressure is reached, and if the pressure ever drops below the recommended amount, bring it back up and start the timing over (NCHFP). Never shorten a time or lower a pressure.
Higher Utah: use the next band up
Utah does not stop at the valley floor. Communities at 6,000–7,000 ft fall in the next band up: add 15 minutes in a boiling-water canner and process at 14 lb on a dial gauge (weighted gauge stays at 15 lb). At 8,001–10,000 ft the additions reach 20 minutes and 15 lb dial. If you are not sure of your elevation, look it up before your first batch — USU Extension's altitude fact sheet lists Utah counties and towns, and the USGS Elevation Point Query Service gives an exact figure for an address. When your elevation sits near a band edge, use the higher band.
After processing: cooling, seals and the one-year rule
Let jars cool undisturbed for 12 to 24 hours, then check every seal before anything goes on a shelf (NCHFP). For the standard two-piece lid, any one of these three tests tells you:
- Press the center of the lid. If it springs up when you let go, the jar is unsealed.
- Tap the lid with the bottom of a spoon. A sealed jar rings high-pitched; a dull sound means no seal (food touching the lid's underside can also dull the sound).
- Look across the lid at eye level. A sealed lid is concave — curved down slightly in the center. Flat or bulging means it may not be sealed.
For sealed jars, remove the ring bands, wash and dry the jars, and store them without the bands — a broken seal is easier to spot, and the bands stay dry. Label and date every jar. An unsealed jar is not shelf food: refrigerate it and use the contents within one week, or reprocess within 24 hours following the tested recipe (NCHFP notes reprocessing costs quality and does not recommend it).
Store sealed jars in a clean, cool, dark, dry place — 50–70°F is best, and never above 95°F. Plan the pantry around one year: for best quality, can no more food than you will use within a year (NCHFP). That year is a quality framing, not a safety cliff — flavor, color and nutrition fade first — which is exactly why rotation matters. Run home-canned jars through the same first-in, first-out habit as the rest of the pantry in the FIFO rotation guide, check them against the shelf-life chart, and store the long-term dry staples alongside them using the long-term food storage guide.
The tools this page assumes
A dial-gauge pressure canner for low-acid foods (have the gauge tested yearly — county extension offices usually do it free) and the basic hand-tool kit. The adjustment tables above are written around this class of canner.
| Item | Priority | How much | Why | Shop |
|---|---|---|---|---|
| Pressure canner (23-quart, dial gauge) Canning | Priority: P1 | How much: 1 canner per household — 23-quart class — holds 7 quart jars, 20 pints or 26 half-pints per pressure load | Why: The only safe way to can low-acid foods (vegetables, meats, soups) is a pressure canner used with USDA-tested recipes — a water bath cannot reach the temperatures botulism spores require. The Presto 01781 is the dial-gauge canner the extension altitude tables are written around; at altitude you adjust its pressure (and water-bath times) per the canning-at-altitude guide. Have the dial gauge tested yearly — your county extension office usually does it free. | Shop: Check price — Pressure canner (23-quart, dial gauge) |
| Canning tool kit (jar lifter, funnel, lid lifter) Canning | Priority: P1 | How much: 1 kit per household | Why: The hand tools every canning session actually uses: jar lifter, wide-mouth funnel, magnetic lid lifter, jar wrench, tongs and a bubble popper/headspace measurer. The Norpro 6-piece set (#599) is the extension-recommended beginner kit — no batteries, nothing electronic to fail mid-session. | Shop: Check price — Canning tool kit (jar lifter, funnel, lid lifter) |